Representative ChuanGu "value"
taste or mechanical watch, probably because of the Christmas holiday and
without wearing long dormant, or travel must be for maintenance, long after not
wearing watch money if want to readjust time, must pay special attention to
operating mode, lest cause gear card tenon fault, internal parts can't run, if
can normal maintenance, watch money need to spend large sums of money
maintenance condition can be reduced to the minimum cost.
The principle of mechanical watch adjusting
time
Long rest for mechanical watch spring,
relaxed to watch money is motionless, at this point, if want to wear, we must
first, and then to wind calibration time, should general manager said, general
mechanical watch in the pine, spring will appear clockwise, minute slow or
quicke phenomenon, so, should first wind, lest calibration time, there is no
standard driving pointer, even automatic refined watches, also should use first
manual tried to 8 minutes to full time calibration, again.
Mechanical watch to cleaning, maintenance
principle: (1), with soft cloth to wipe (2) soap water with soft cloth to wipe
(3) water dry soft cloth to wipe (4) tumble (5) taboo don't literally send
ultrasound cleaning
Whatever had been engaged in the watches
water activities, need to do "maintain", especially after the sea
salt water soak, the pool of chemicals, and filter are easily cause watches
waterproof gasket erosion, hardening; Some maintenance is simple, at home with
a soft cloth with a few soap water cleaning metal and waterproof rubber strap,
finally and with wet cloth to remove traces of soap water wipe after, can
tumble reached a preliminary maintenance performance, meanwhile, must not will
watch directly to have ultrasound equipment place do cleaning, because
ultrasound cleaning have points of strong, weak different frequency, a but not
used ultrasound frequencies, there would be a loose parts inside.
Watches can receive principles: (1) check
the maintenance period (2) check whether need to take out the battery quartz
watch
Long time of use or long time paragraph,
must receive special attention to watch the watches general mechanical
maintenance period, the maintenance period watches about 3 ~ 4 years, once more
than this deadline, atlas internal lubricating oil stains, external to dry it's
easier to atherosclerosis, waterproof gasket barely use easy occurrence of
mechanical parts fault and fill and lubricant dry stains cause parts, early
wear will also affect operation, and can only see time for accuracy of lower,
as time passes, when to stop operation, internal parts has been very serious,
loss of to this extent, "micro little" maintenance cost becomes
"large" parts repair expenses.
In addition to mechanical watch maintenance
to avoid the problem of maintenance, quartz watch in addition to the internal
parts to drive lubricating with waterproof problems outside, in long period not
wear situations, if batteries have been used for a long time, had better not on
another case to make long-term receive within, lest battery failure, not only
cannot supply problems, might even be a battery liquid leakage must replace the
internal parts.
Mechanical watch using quick dial the
button should note: (1) inquires the instructions (2) will be time to adjust to
five to seven speed-dial buttons to use position
Time precision, complex enough adjusting
mechanical watch performance, some must follow manner, should be noted the
President, each piece of complex mechanical watch sold in performance of the
metropolis when operating instructions, even with Shared machine watches,
because table factory be modified, appear parts in a different way, when
operating configuration of the order must be special attention, therefore,
browsing operation explanation is the first priority. If really afraid
troublesome, it is required to use special attention to the correct speed-dial
buttons, when activated when speed-dial performance must be adjusted clockwise,
in the right place, ability won't cause performance parts have card into the
correct position, but were forced to beat speed-dial buttons rotating cause
problems. Failure parts
Speed-dial buttons during operation outside
besides watching the operating instructions, the overwhelming majority of
watches should try to avoid the until 4 a .m.
at eight o 'clock at night time, but also the most troubled consumer is the
time, because almost all free adjustment is in the evening; At this point, can
take strain way, is five to seven o 'clock repatriated clockwise position, make
watch money already prepared under the action of a gear is stuck at this time
to loosen, then it won't happen speed-dial adjustment problems, but some brand
watches gear set at noon, if think executive conversion action was noon is no
problem and direct speed-dial buttons adjustment can also lead to parts
disorders, therefore, will put five to seven hour between the majority of the
most suitable position watches.
Mechanical watch maintenance gist: which to
buy back to where
If watches the problem appears to shops
need, which to buy it back to where, if really found not in the right, may also
directly back to agents, please agents identification, processing, but like the
consumer in overseas purchase, we must consider carefully looking for credit
problems of shops for processing, the watch money in the past have happened
internal parts not original condition, this is generally not horological
professional consumer can identify with, to avoid disputes or stores and agent
buy original for main consulting object.
